网站首页 | 产品展示 | 产品总汇 | 润滑油知识 | 新闻资讯
工业润滑油专区

 
产品展示 >> Castrol Aircol PD32,46,68,100,150/Castrol Aircol PD 32,46,68,100,150
Castrol Aircol PD32,46,68,100,150/Castrol Aircol PD 32,46,68,100,150详细说明 (浏览1247次)
Aircol PD Range
Air compressor lubricants
Description
The Castrol Aircol PD range of compressor lubricants are based upon highly refined mineral oils and carefully chosen
additives. They are intended for the lubrication of both reciprocating and rotary air compressors.
Application
The Castrol Aircol PD grades are ashless oils recommended for the lubrication of rotors, bearings and gears in rotary
compressors, especially the oil flooded screw type with delivery temperatures of up to 120°C.
The Castrol Aircol PD compressor oils exhibit low carbon forming tendencies and meet the requirements of the DIN
51506 VD-L classification for reciprocating compressors having air discharge temperatures up to 220ºC.
Selection of the required viscosity grade should be based upon the compressor manufacturers' recommendation,
however as a general guide Castrol Aircol PD 32 and 46 are suitable for oil flooded rotary compressors, whilst Aircol PD
68 and 100 would be selected for lubricating the crankcase and cylinders of reciprocating compressors. Castrol Aircol PD
150 is recommended for sliding vane compressors, or for reciprocating units operating at high ambient temperatures.
Castrol Aircol PD range is classified as follows:
DIN 51506 VD-L.
ISO 6743/3 Compressor Oils - DAA and DAB for reciprocating air compressors, DAG for rotary air compressors.
Castrol Aircol PD meets the requirements (for appropriate viscosity grade) of major compressor manufacturers such as
Atlas Copco, Champion, Sullair, Compair/Broomwade, Ingersoll-Rand, Kaeser and Bauer.
Features and Benefits
Excellent water separation characteristics which allow condensation to readily separate from the oil, minimising
the risk of emulsions which could block the oil separator element.
Fully inhibited against corrosion which enables protection even when operating under humid conditions.
Good thermal stability, low volatility and low carbon formation reduces the risk of fire and explosion and leads to
longer operating life (up to 2000 hours).
Low deposit forming tendencies extends oil change intervals and provides longer air filter life which contributes to
a reduction in maintenance costs.
Excellent coalescing properties mean little carry over of oil in the air stream.
Page 1 of 3Technical Data
Name Method Units Aircol
PD 32
Aircol
PD 46
Aircol
PD 68
Aircol PD
100
Aircol PD
150
Relative Density at 15°C ASTM D4052 /
ISO 12185 g/ml 0.874 0.876 0.881 0.885 0.887
Kinematic Viscosity at 40°C ASTM D445 /
ISO 3104
mm²/
s
32 46 68 100 150
Kinematic Viscosity at
100°C
ASTM D445 /
ISO 3104
mm²/
s
5.57 6.67 8.57 11.4 14.5
Viscosity Index ASTM D2270 /
ISO 2909 110 100 100 98 98
Foam Sequence I ASTM D892 /
ISO 6247 ml/ml 30/0 30/0 30/0 30/0 30/0
Open Flash Point ASTM D92 /
ISO 2592 °C/°F 226/439 232/450 232/450 253/487 256/493
Pour Point ASTM D97 /
ISO 3016 °C/°F -21/-6 -21/-6 -21/-6 -12/10 -9/16
Demulsification at 54°C ASTM D1401 /
ISO 6614 mins 15 15 15 - -
Demulsification at 82°C ASTM D1401 /
ISO 6614 mins - - - 20 20
Rust Test, Procedure B ASTM D665B - Pass Pass Pass Pass Pass
Conradson Carbon
Residue Oxidation Test DIN 51352-2 % wt 0.7 0.7 0.7 < 3 < 3
The above figures are typical of those obtained with normal production tolerance and do not constitute a specification.
Page 2 of 3Care and Handling
Avoid prolonged or repeated contact with skin. Wash thoroughly after handling.
Packaging and Storage
All packages should be stored under cover. Where outside storage is unavoidable drums should be laid horizontally to
avoid the possible ingress of water and the obliteration of drum markings. Products should not be stored above 600C

上一产品: Mobil Gas Compressor Oil美孚气体压缩机油
下一产品: castrol aircol sr 32/46/68/castrol aircol sr32/46/68